io.github.magiccadai/magicon

Tools

• check_grounding

  Check a draft passage against the engine results computed in THIS session. It returns every figure no engine produced, and every claim it checks that the results do not support or contradict (for example a solver score called a loss), each in `findings` with the reason. Run it before publishing or handing over a report, fabrication sheet, BOM summary or any other figure-bearing deliverable built from these tools. It computes nothing and adds no evidence — it only reports what the results back. Fix each finding the way its `why` says: quote the engine's own value, call the tool that computes it, correct the wording, or say plainly in the text that the figure is not from a tool.

  shallow
• design_rf_chain

  Design a complete RF transmitter chain with the convergent orchestrator: selects the driver, PA, filter, and connector (the signal source is the user's input power by default — no VCO unless one is explicitly the generator), matches drive power between stages, inserts a pre-driver or attenuator when needed to reach the target output power, and returns the BOM plus a convergence summary (achieved vs target output). When the BOM's pricingCoverage is 'partial', total_usd is a subtotal of pricedLines of totalLines parts: never call it the total, and state no figure for the unpriced parts.

  shallow
• design_rf_receiver

  Design or analyse a superheterodyne RECEIVER. Selects catalog parts for each slot (limiter, LNA, image filter, mixer, LO, IF filter, IF amp, step attenuator) and returns the frequency plan (image, half-IF, LO leakage), the cascaded noise figure, noise floor, MDS, sensitivity, SFDR and dynamic range, plus the ADC interface (sample rate, Nyquist zone, ENOB, jitter limit). Pass rfFrequencyHz to design one; pass stages[] only for a bench receiver the user described with their own numbers.

  shallow
• design_tr_module

  Design a T/R (transmit/receive) module that shares ONE antenna between a transmitter and a receiver. Designs both chains through the existing engines, selects the shared front end (a T/R switch, or a circulator with a receive-path limiter), and returns four safety budgets: TX-to-RX isolation against the receiver's damage limit, the receive window left after switching and limiter recovery, limiter leakage driving the LNA into compression, and transmit power against each part's survivability rating. Pass frequencyGhz and targetOutputPowerDbm to design one; pass txPeakPowerDbm and isolationDb only to check a front end the user already described with their own numbers.

  shallow
• run_compliance_analysis

  Audit the solved stackup against PCB standards (IPC-2221, IPC-6012, IPC-4101, MIL, UL-94, RoHS, REACH): per-rule pass/fail with severities and remediation. Reuses the engine behind POST /api/compliance/check. Layers are derived from the solved stackup and standards default to IPC-2221 + IPC-6012 Class 2 — call with no arguments once a stackup exists.

  shallow
• run_link_budget

  Compute a cascaded RF link budget. For the chain just designed, call with NO arguments — the server derives stages and input power from the design. Pass stages + inputPowerDbm only for a bench/hypothetical chain. Returns per-stage output power, cumulative gain, Friis cascaded NF, gain-referred reciprocal-sum cascaded OIP3, P1dB headroom warnings, and overall risk. Optionally pass bandwidthHz (and requiredSnrDb) to also get the receiver noise floor, MDS, sensitivity, SFDR, and instantaneous dynamic range.

  shallow
• run_pdn_analysis

  Run a PDN (power delivery network) impedance analysis: interplanar plane-pair capacitance, multi-cap decoupling impedance vs. target impedance, violations, and recommended decoupling caps. Reuses the Phase-25 engine behind POST /api/pdn/analyze. Inputs are derived server-side from the solved stackup, the BOM's PDN passives, and the power-tree rail — call with no arguments once a design exists.

  shallow
• run_stackup_solver

  Run the impedance-aware stackup constraint solver to find optimal PCB configurations. Use when the user wants ranked material/thickness/copper solutions for a given layer count and frequency. Returns scored and ranked feasible stackups. Each solution's prepreg_thickness_mm is the catalog BASE (pre-lamination) ply thickness, so the per-ply numbers do NOT sum to total_thickness_mm — the total uses the pressed thickness, 0.04064 mm thinner per prepreg ply. Report both as returned; never 'correct' one to match the other.

  shallow
• run_thermal_analysis

  Run a full PCB thermal analysis: via array Rth, junction-to-ambient stack, Kennedy spreading, Coffin-Manson barrel stress, Timoshenko warpage, and resin-flow estimation. Mirrors POST /api/stackups/{id}/thermal-analysis. Call with no arguments once a design exists: the server takes power_w from the designed chain's dissipated power and defaults ambient_c to 25 C. The result carries `recommendations` (thermal vias, copper, plating) — answer adjustment questions from those entries. If the user states a heatsink or airframe spreader, pass `heatsink` (θcs, θsa and mount, all three as stated — never guessed); Tj is then computed through it instead of still-air convection.

  shallow

Embed this server’s score

Tool count and median score across every tool in this server’s corpus — honest in a way a single cherry-picked tool’s badge wouldn’t be.

[![Vouch score](https://vouch.tools/api/servers/2945665a-012e-427a-9628-c455e1f0a601/badge.svg)](https://vouch.tools/servers/2945665a-012e-427a-9628-c455e1f0a601)